● Triangle shap bent tube design
● For all industries, and all process and custody transfer applications.
● Universal measuring principle for liquids and gases
● Multivariable measurement- simultaneous measuring of mass flow, density, temperature
● High measuring accuracy: typically ±0.2%, ±0.1% o.r., optionally: ±0.05%
● Measuring principle independent of the physical fluid properties and the flow profile
● Easy to install (low risk of gas bubble inclusion)
● No recalibration required after fluid change
● No installation straight line necessary
● No temperature or pressure compensation necessary
● No periodical recalibration required
The mass flowmeter consists of a sensor and a transmitter. The mass flow meter is equipped with digital signal processor (DSP) -based digital transmission equipment, and integrates digital closed-loop vibration control (DLC) signal processing, sensor calculation and diagnostic functions, and has high measurement accuracy and extensive capabilities. And excellent reliability for you. On-line node configuration, fault diagnosis and data logging can be performed directly through HART or PC via Modbus to communicate with the communicator. The flow meter will not only calculate the process volume flow, cumulative volume and component ratio. TS series flow meters can also provide mass flow, density and temperature online in real time.
Coriolis mass flow meters are the most accurate measuring method in the world. The Coriolis measuring principle is used in a wide range of different branches of industry, such as the life sciences, chemicals, petrochemicals, oil and gas, food, and- no less importantly - in custody transfer applications. Coriolis flowmeters can measure virtually all fluids: cleaning agents, solvents, fuels, crude oil, vegetable oils, animal fats, latex, silicon oils, alcohol, fruit solutions, toothpaste, vinegar, ketchup, mayonnaise, gases or liquefied gases.
The Sincerity DMF series triangle shape is the standard high performance coriolis mass flowmeters for the process industry. The U shape bent tube meter offers superior performance and high accuracy in virtually any application. From process control in (petro) chemical applications to concentration measurements in the food and beverage industry to custody transfer filling and transport measurements in the oil and gas industry. Its high-end options also make the DMF-1 Series U-shape the optimum device for cryogenic media like Liquefied Natural Gas (LNG) with temperatures down to -200°C / -392°F as well as applications involving high operating temperatures (up to 350°C / 662°F) or pressures (up to 250 barg / 3700 psig).
Coriolis flow measuring principle
Each Coriolis flowmeter has one or more measuring tubes which an exciter causes to oscillate artificially. As soon as the fluid starts to flow in the measuring tube, additional twisting is imposed on this oscillation due to the fluid’s inertia. Two sensors detect this change of the tube oscillation in time and space as the “phase difference.” This difference is a direct measure of the mass flow.
In addition, the fluid density can also be determined from the oscillation frequency of the measuring tubes. The temperature of the measuring tube is also registered to compensate thermal influences. The process temperature derived from this is available as an additional output signal.
How does a Sincerity Coriolis flow meter measure mass flow and density?
Coriolis mass flow measurement is the MOST ACCURATE FORM for a flow measurement for a wide range of industrial processes. Each Coriolis flowmeter has one or more measuring tubes.
As soon as the fluid starts to flow in the measuring tube, additional twisting is imposed on this oscillation due to the fluid's inertia. Two sensors detect this change of the tube oscillation in time and space as the “phase difference.”
Phase difference= mass flow
Oscillation frequency= density
MICRO BEND V-HAPE
CNG/ LNG/ LPG dispensers
High viscosity & high pressure applications
Minimum flow rate
Maximum flow rate
Flow range calibrated can be compressed. The classic typical type with more than 30 years histroy.
More popular with cng/lpg/lng dispensers, with even smaller size with most advanced technology.
More popular with pipeline size bigger than dn80, with smaller size and lower pressure drop. Most suitable for high viscosity liquids.
See charts below
ANSI, DIN, JIS, or Sanitary Tri-Clamp flanges, etc. ( Connections can be customized)
16 bar (230 psi), [Optional 40 bar (580 psi), up to 1000 bar (14504 psi)]
304 Stainless Steel
Measuring Tube Material
316 L SS, HC Hastelloy, 316L SS + PTFE, HC + PTFE, etc. ( materials can be customized)
Process Temperature Range
-50 to 15°C (-58 to 302°F)
Remote Type (-R)
-50 to 35°C (-58 to 662°F)
-40 to 55°C (-40 to 131°F)
(5 to 95%) RH at 25°C (77°F)
0.2/ 0.1/ 0.05% (Liquid), 0.5% (gas)
0.2 to 3.0 g/cm3
± 0.002 g/cm3, ± 0.001 g/cm3
ATEX, CE, ISO9001, ISO14001, OHSAS18001
RS485 (RTU Modbus), HART (-HART option)
0 to 10 kHz
4 to 20 mA
24VDC, 220VAC (universal power source option)
|1||Suffix Code||Process Connection Size||Measuring Range|
|3CLS10||10mm||0-1.5t/h For high viscosity liquids/ gases, etc.|
|3CLS15||15mm||0-2.0t/h For high viscosity liquids/ gases, etc.|
|3CLS20||20mm||0-2.5t/h For high viscosity liquids/ gases, etc.|
|3CLS25||25mm||0-10t/h For high viscosity liquids/ gases, etc.|
|3||Code||Sensor Temperature (Above 250°C and below -50°C the transmitter are separated installation.)|
|XX||With customer specified pressure|
|5||Code||Material of wetted parts|
|A||Stainless Steel 316L|
|D||Inner Wall Surface with PTFE spray(Large size only)|
|E||Special Order: With customer specified material|
|F||Flange GB/T 9123.1-2000 ANSI Weld Neck Flanges-ANSI Bl 6.5|
|T||Special oder, with customer specified connection|
|A||Stainless Steel 304|
|B||Stainless Steel 316L|
|B||Seperate Installation(connector length),with holder|
|A||4-20mA (Instant flow rate/density) 0-10KHz( Instant flow pulse output ）, RS485 Modbus RTU|
|B||4-20mA (Instant flow rate/density) 0-10KHz( Instant flow pulse output ）, RS485 Modbus RTU，HART|
|F||Factory, Factory certificate|
|I||GB, Third party certificate|
|B||Diecasted aluminum alloy housing Wiring Hold Size： M2Ox1.5|
|C||Diecasted aluminum alloy housing Wiring Hold Sze： 1/2"NPT|
|A||Exd ib ll CT6 Gb|
Nominal line size
Maximum flow rate
Copyright © 2020 Beijing Sincerity Group. | Reservados todos los derechos.